RSA 478:1-a · Recording of Plats

478:1-a Recording of Plats. –

Copy link

I.

No register of deeds shall file or record a plat of a subdivision, or a plat prepared for the purpose of showing existing property lines, if such plat has not been prepared and certified by a licensed land surveyor, since July 1, 1981, or by a registered land surveyor between January 1, 1970 and June 30, 1981, and any such filing or recording shall be void. For the purposes of this section the definition of the word "subdivision" shall be that contained in RSA 672:14. A "plat" for the purpose of this section shall be a map of a specific land area whose boundaries are defined by metes and bounds. A plat may show:

Copy link

(a)

Newly created parcels, streets, alleys, and easements as in a subdivision; or

Copy link

(b)

A lot-line-adjustment or site plan depicting existing parcels defined by legal descriptions contained in deeds, grants, or other legal documents.

Copy link

II.

Each register of deeds shall establish a policy for providing adequate space, on the plat, for recording the registry plan number and recording information.

Copy link

III.

The register of deeds shall refuse for recording any map that does not meet the definition of a plat under paragraph I and any plat that does not contain the information or meet the specifications required by this section. Construction plans, construction details, and maps that do not define the limits or extent of legal rights or interest in land shall not be recorded.

Copy link

IV.

All plats shall be drawn with the following sizes: 8.5' x 11,' 11' x 17,' 17' x 22,' 22' x 34,' or such specifications and sizes as may be required by the register of deeds. The material composition of the plats shall be suitable for electronic scanning and archiving by the register of deeds.

Copy link

V.

All plats shall have a minimum of 1/2 inch margins on all sides.

Copy link

VI.

All text and dimensions shall be legible for reproduction, and the text sizes shall be no smaller than .08 of an inch for mechanical drafting and 1/8 inch for hand drafting.

Copy link

VII.

All certifications, seals, and approval blocks shall have original dates and signatures in a legible, permanent black ink.

Copy link

VIII.

All title blocks shall be located in the lower right hand corner, when possible, and shall indicate the following:

Copy link

(a)

Type of survey, such as a boundary survey, subdivision, American Land Title Association (ALTA) survey, or lot line adjustment.

Copy link

(b)

Owner of record.

Copy link

(c)

Title of plat or development.

Copy link

(d)

Tax map number.

Copy link

(e)

Name of the town in which the parcel is located.

Copy link

(f)

Plat and revision dates.

Copy link

IX.

All plats shall have a scale both as a written and graphic representation.

Copy link

X.

All plats shall have a north arrow with reference to magnetic grid or astronomic north, as applicable. The north arrow shall be labeled with its reference direction.

Copy link

XI.

Shading over any text shall not be permitted on any plat. Cross hatching or other hatching at a scale large enough not to interfere with text legibility, before and after reproduction, may be permitted.

Copy link

XII.

No lines, whether hatching, boundary lines, or topographic contours shall obstruct or interfere with the legibility, either before or after reproduction, of any bearings, dimensions, or text.

Copy link

XIII.

The minimum line widths on plats shall not be smaller than .01 inches.

Copy link

XIV.

The register of deeds shall not refuse to record a plat under this section for failure to comply with a law, regulation, or ordinance adopted after the date the site plan or plat was approved by the municipal planning board. Source. 1988, 233:3. 1995, 303:1. 2004, 103:1, eff. Jan. 1, 2005. 2025, 186:4, eff. July 1, 2025.

Copy link